INDUSTRIAL TRAINING REPORT

 

 

 

GLOBAL INSTITUTES OF MANAGEMENT AND EMERGING TECHNOLOGY, AMRITSAR

                DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING

 

GUIDELINES FOR SIX MONTH INDUSTRIAL TRAINING REPORT

These guidelines for successful completion of Six month industrial training

are to facilitate in effective and uniform regulation of training being carried out by

Undergraduate students in 8th semester. Department of Electronics and

Communication Engineering department will designate one faculty member as the

Assistant Training and Placement officer (ATPO) who will get all the training

Arranged with the help of Training and Placement Cell of the college and will keep

All records. All Students will contact the Concerned ATPO for any query or

Information.

 

Training Monitoring:

 

Six month industrial training will be monitored by the ATPO (ECE) with

Consultation of the TPO. This monitoring activity will be spread over one semester

i.e. 8th semester.

 

 Award of Sectionals (TA):

 

The evaluation of the training will be based on the report submitted by the

ATPO after the mid semester evaluation and interaction with the supervisor of the

Student in the industry.

 

Point to Remember during training:

• All students are advised to be sincere, honest and punctual during the training period.

• They should be polite and cooperative at the training place.

• Any complaint if reported will seriously deal with.

• All students are to ensure that their confirmation letters have been received at TPO office. If someone’s confirmation letter has not been sent that they should ask their supervisor to do the needful.

• All students will have to submit the synopsis and objectives of the training within the first month of their training.

• At the end of the industrial training the Supervisor (from concerned industry) is to submit the evaluation report in the sealed envelop to the TPO, SSSETC, Gurdaspur immediately.

• All students to ensure that their daily diary is properly signed by their supervisor before submission to the college for final evaluation.

• The six month training report should be submitted in the proper format already specified.

• All Students should come prepared with the power-point presentation regarding their industrial training (Based on CHAPTER I to V in the training report submitted). Which will be most probably in of April/May All Students will be asked to submit the power-point presentation on a CD along with the one hard bond copies of training report on the day of external viva presentation.

• The External Evaluation/viva-voce by external examiner will be held April/may, and the exact date will be intimated separately on the day of 1st presentation after completion of training.

• No report will be accepted if not submitted in the specified format.

Hence all students on training are advised to strictly follow the specified format given below.

• All students should complete their training reports and presentations in the specified format for  mid term viva and final report.

 

 

 

 

Guidelines for Training Report Preparation (Mid-term and Final Report):

Please go through the following pages:

FORMAT OF COVER PAGE (Hard Bound)

 

SIX MONTH INDUSTRIAL TRAINING REPORT (14pt)

 

                                                               ON

 

                                               TITLE OF TRAINING (24pt)

 

                                                  COMPLETED AT (14pt)

 

                                   NAME OF THE COMPANY /FIRM(14pt)

 

 

 

company logo 

 

 

 

 

                   Submitted to :                                        Submitted By

                   Name of HOD                                         Name of Student

                                                                                 ( Class Roll No.)

                                                                                  Univ Roll No.

 

 

 

 

 

DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGG.

GLOBAL INSTITUTES OF MANAGEMENT AND EMERGING TECHNOLOGY, AMRITSAR

Apr 2016

 

 

 

 

 

 

 

 

 

 

FORMAT FOR INSIDE COVER PAGE:

SIX MONTH INDUSTRIAL TRAINING REPORT (14pt)

 

ON

 

TITLE OF TRAINING(24pt)

 

COMPLETED AT (14pt)

 

NAME OF THE COMPANY /FIRM(14pt)

 

SUBMITTED IN PARTIAL FULFILLMENT FOR AWARD OF DEGREE OF(12pt)

BACHELOR OF TECHNOLOGY

 

IN

 

              ELECTRONICS AND COMMUNICATION ENGINEERING (14pt)         

 

                                                               

 

 

 

 

 

  SUBMITTED TO :                                            SUBMITTED BY: 

  NAME OF HOD                                                NAME OF STUDENTS (14pt)

                                                                          UNIV. ROLL NO.)

                                                                                                                                                                                                                                                          

 

 

 

 

DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGG.

GLOBAL INSTITUTES OF MANAGEMENT AND EMERGING TECHNOLOGY, AMRITSAR

 

                                                     Apr, 2016

 

 

 

 

 

 

Text :

 

The text should be typed in 12 font size Times New Roman style in double

spacing on one side of A4 size page (Executive Bond) only. The Captions for

figures should be typed at the its bottom for example 4th figure in Chapter 3 should be

captioned as Fig. 3.4 Title of Figure. The captions for tables should be typed at its top for

example 7th table in Chapter 3 should be captioned as Table. 3.7 Title of Table.

 

 Arrangement of Contents of Project Report

 

The sequence in which the project report should be arranged and bound is as follows:

 

1. Cover Page & Title Page

2. Certificate of Training issued by Industry/firm/company

 3. Abstract

4. Acknowledgement

5. Table of Contents

6. List of tables

7. List of Figures

8. List of Symbols, Abbreviations

9. Chapters I, II, III, IV, V

10. Appendices

11. References

 

 

CHAPTER I

   INTRODUCTION

      1.1 Introduction

      1.2 Necessity

      1.3 Objectives

       1.4 Theme

       1.5 Organization

 

 CHAPTER II

               LITERATURE SURVEY RELATED WITH TRAINING

Literature Survey Related information available in standard Books/Manuals,

Journals, Transactions, Internet Websites etc. and services offered by companies

 

 CHAPTER III

             TRAINING WORK

Training Work Module Development

.. Computational

.. Experimental

.. Mathematical

.. Statistical

.. Conceptual

.. (Out of above methods at least one method is to be used for the training module)

 

 

 

 

CHAPTER IV

EVALUATION OF TRAINING

Evaluation may be done based on following:

.. Analysis of training done

.. Methods normally used are Analytical /Computational/Statistical/Experimental/ or Mathematic       

.. Results at various stages may be compared with various inputs

.. Output at various stages and related information/parameters

.. Justification for the training results

 

CHAPTER V

CONCLUSIONS AND FUTURE SCOPE OF TRAINING

5.1 Conclusions & objectives achieved

5.2 Future Scope

5.3 Applications

 

Numbering of Chapters, Sections and Sub-sections:

The numbering of Chapters, division and sub-divisions should be done using Arabic

numerals only and further decimal notation should be used for numbering the divisions and

subdivisions within a chapter. For examples sub-division 4 under division 3 belonging to

chapter 2 should be numbered as 2.3.4.

 

 

 

 

 

Numbering of Equations:

 Equations appearing in each Chapter should be numbered serially, the numbering

Commencing fresh for each Chapter or Appendix. For example, an equation appearing in

Chapter 2, if it happens to be the eighth equation in that Chapter 2 should be numbered (2.8).

While referring this equation in the body of the report it should be referred to as Equation

(2.8).

 

 List of References:

Any work of other researchers, if used either directly or indirectly, the origin of the

material thus referred to at appropriate places in the report should be indicated. The citation

may assume any of the standard form (preferably IEEE, or other international Journal

Publishers such as Elsevier, Kluwer, Pergamum etc.).

 

 For example: Rice, I.G., 1982, “The reheat Gas Turbine With Stream Blade Cooling-A

Means of Increasing Reheat Pressure, Output, and Combined Cycle Efficiency.” ASME

Journal of Engineering for Power, Vol 104, pp. 9-22

 

Page Dimensions and Margin:

The dimensions of the final bound 2 copies report should be Standard A4 size

(297mm x 210mm) paper may be used for preparing the copies. The Training Report (at the

time of submission) should have the following page margins:

 

Top and Bottom edge: 25 mm (1 inch)

Left and right side: 32 mm (1.25 inches & 1 inch)

 

Page Numbering:

All pages numbers should be typed at the center of page bottom. The preliminary

Pages of the report (such as Title page, Acknowledgement, Table of Contents, List of tables

And figures, Notations, Abbreviations etc.) Should be numbered in lower case Roman

Numerals.

 

Size of Report:

The size of report should not exceed 80 Pages of typed matter reckoned from the First page of Chapter 1 to the last page of the Appendix.

Binding Specifications:

Report submitted (1 copies) should be bound in Black color hard binding with golden words.

 

 Number of Copies to be submitted:

one copies for departmental library are to be submitted before ______ due date______ to the Department.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

A PROJECT REPORT

ON

TWO MONTHS INDUSTRIAL TRAINING

AT

NAME OF THE COMPANY /INSTITUTE, CITY

SUBMITTED TO

 “Punjab Technical University”

 IN PARTIAL FULFILLMENT OF THE REQURIMENT OF THE  AWARD OF DEGREE OF

BACHELOR OF TECHNOLOGY

IN

ELECTRONICS & COMMUNICATION ENGINEERING

 

 

 

 

 

 

 

                     

  Submitted to :                                                                    Submitted By                                                             

  Name of HOD                                                                    Name of Student                                                                                              

                                                                                             Univ Roll No.                                      

                                                                                              

                                                                                                  

 

  

 

  

                                               

 

 

Department of Electronics & Communication Engineering

GLOBAL INSTITUTES OF MANAGEMENT AND EMERGING TECHNOLOGY, AMRITSAR

 

     Batch (2012)   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CERTIFICATE

 

It is to certify that NAME OF STUDENT (ROLL NO.) student of Electronics and communication Engineering Department,GlobalInstitutes Of Management and Emerging Technology,Amritsar has completed the industrial/institutional Training at “COMPANY /INSTITUTE’S NAME” for the partial fulfillment of the requirement for the award of Bachelors of Technology (Electronics and Communication Engineering) Degree of PTU, Jalandhar.This is a record of student’s own study carried under my supervision & guidance.

This report has been submitted for the award of B.Tech degree.

 

 

                                                                                 

  Head of Department                                                              Director

   (ECE)                                                                                     GIMET,ASR.                                                                                                                                                                                                                                      

                                                                                                          

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ACKNOWLEDGEMENT

 

I am highly greatful to NAME OF INDUSTRIAL/INSTITUTINAL GUIDE for allowing me to do this project work. It is truly a matter of greate pleasure me to express my sincere thanks and gratitude to NAME OF INDUSTRIAL/INSTITUTINAL GUIDE for his suprivision and encouragement throughout this project. We are highly obliged to “NAME OF ALL HELPERS OF U IN UR TRAINING / PROJECT WORK”for their guidance, kind concern and encouragement throughout this project.

I am immensely indebted to NAME OF INDUSTRIAL/INSTITUTINAL GUIDE for the invaluable help that he rendered at every step of this project. It is a wonderful experience to be a part of. “COMPANY INSTITUTE’S NAME” Where we work under brilliant minds. We owe our deep regards for the supporting and kind staff authorities who are helping me In my lean patches during these two months. The knowledge we are gaining throughout our studies have the practical implementation during this period. We are grateful to all the staff of “COMPANY /INSTITUTE’S NAME”

 

 

 

                                                                                                               

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ABSTRACT

For example >

The core idea that makes CDMA possible was first explained by Claude Shannon, a BellLabs research mathematician Shannon’s work relates amount of information carried, channel bandwidth, signal- to –ratio, and detection error probability. It shows the theretical upper limit attainable. CDMA is a unique method of wireless communication. There are unique aspects of this type of communication that impact repeats. Understanding the basics of CDMA will help with repeater planning installation, and optimization.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INDEX

 

EXAMPLE

S.No

Contents

Page No

1

Company Profile

1-4

2.

Introduction To Cellular Growth                                                                                                                                 

5

2.1

Reliance FWP 

5-6

2.2

CDMA                                                                               

6-13

2.3

GSM

14

2.4.

GPRS

15-16

2.5

EDGE

16

2.6

3G                               

17

3

Cellular Architecture

18

3.1

Clusters

18

3.2

Frequency Reuse

18-19

3.3

Cell Spliting

20

4

GSM Concept

21-22

4.1

History Of GSM

22-23

4.2

GSM Architecture

23-24

4.3

GSM Servics

24-26

4.4

Frequency Spectrum

26

5

Introduction To Various Equipment

27-28

6

Practical Workdone

29-31

 

© 2012 Shamsher777.n.nu. All Rights Reserved.

This website was built using N.nu - try it yourself for free.(info & kontakt)
UA-39380082-1